I was having an issue where my T41P phones were getting provisioned with IPv4 & IPv6 - even though I specified in default settings yealink_ip_address_mode=0 for IPv4 only. Checked the y000000000036.cfg, which was setting it correctly. The issue was that {$mac}.cfg was overriding the correct setting. There were several instances of "network.ip_address_mode = 2" in this file, which specifies ipv4&ipv6. I changed all 5 of those entries in this file to pull from the default setting {$yealink_ip_address_mode} rather than just setting a static value of 2. I don't know why it has this listed in this file 5 times. But, this change resolved my issue and will force the T41P provisioning to follow FusionPBX default settings.
* Fix the registration failed after provision Flyingvoice phone.
* Fix the parameter configuration of Flyingvoice not displayed in the Default Settings
* Fix: after configuring SIP line 1 of Flyingvoice phone, other SIP lines are disable and the configuration parameters of Flyingvoice are not displayed by default settings.
* Fix after configuring SIP line 1 of Flyingvoice phone, other SIP lines are disable.
* Fix the configuration parameters of Flyingvoice are not displayed by default settings.
* Fix: when only one sip line's shared line is enable, the shared lines of all SIP lines will be enable.
* Fix: unable to generate configuration file of Flyingvoice due to syntax error.
* Add the P1X, P2X, P3X, P5X, i86Box, iMetalBox, audioKit Series for Flyingvoice in Devices.
* Update all model templates of Flyingvoice.
Added a line to set SRTP encryption. the default setting yealink_srtp_encryption was not setting properly to my T56a devices. I downloaded my config files and did not find an entry for srtp at all.
compared with the t54w template and it did have a srtp setting. So I pretty much stole the line from the T54w template and dumped it in here.
The T54w template is vastly superior to this one and this probably needs a rewrite to bring it in line.
Tested on my T56a and it at least gets the job done.
* Fix the registration failed after provision Flyingvoice phone.
* Fix the parameter configuration of Flyingvoice not displayed in the Default Settings
* Fix: after configuring SIP line 1 of Flyingvoice phone, other SIP lines are disable and the configuration parameters of Flyingvoice are not displayed by default settings.
* Fix after configuring SIP line 1 of Flyingvoice phone, other SIP lines are disable.
* Fix the configuration parameters of Flyingvoice are not displayed by default settings.
* Fix: when only one sip line's shared line is enable, the shared lines of all SIP lines will be enable.
* Fix: unable to generate configuration file of Flyingvoice due to syntax error.
* Add the P1X, P2X, P3X, P5X, i86Box, iMetalBox, audioKit Series for Flyingvoice in Devices.
Add grandstream_missed_call_log, grandstream_missed_call_notification, grandstream_missed_call_backlight, grandstream_firmware_upgrade_protocol, grandstream_onhook_dial_barging, grandstream_transfer_mode_via_vpk, grandstream_enable_call_features.
Add condition on grandstream_distinctive_ringtone_name_1, and grandstream_distinctive_ringtone_name_2.
Update Connection request user/pw to work better with GDMS.
On grandstream_wallpaper_url, use current setting name on GRP2613
* allow setting hanging group mode on a per line basis for grandstream dp bases.
* Keep grandstream_hanging_group_mode for better backwards compatibility.
* Added two new minor hardware revisions, the CP925 and T42U, and added the voice.tone.country = {} to all templates, previously missing on most
* Minor typo from a wrong window issue, and removing the commented examples for easier grepping
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
* Update y000000000150.cfg
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
