diff --git a/resources/templates/provision/yealink/w56p/{$mac}.cfg b/resources/templates/provision/yealink/w56p/{$mac}.cfg
new file mode 100644
index 0000000000..73b2b0e8ec
--- /dev/null
+++ b/resources/templates/provision/yealink/w56p/{$mac}.cfg
@@ -0,0 +1,1265 @@
+#!version:1.0.0.1
+
+##File header "#!version:1.0.0.1" can not be edited or deleted.##
+
+#######################################################################################
+##                                   Account1 Settings                               ##
+#######################################################################################
+
+#Enable or disable the account 1; 0-Disabled (default), 1-Enabled;
+account.1.enable = 1
+
+#Configure the label displayed on the LCD screen for account 1.
+account.1.label = {$display_name_1}
+
+#Configure the display name of account 1.
+account.1.display_name = {$display_name_1}
+
+#Configure the username and password for register authentication.
+account.1.auth_name = {$user_id_1}
+account.1.password = {$user_password_1}
+
+#Configure the register user name.
+account.1.user_name = {$user_id_1}
+
+#Configure the SIP server address.
+account.1.sip_server_host = {$server_address_1}
+
+#Specify the port for the SIP server. The default value is 5060.
+account.1.sip_server_port = {$sip_port_1}
+
+#Enable or disable to use the outbound proxy server; 0-Disabled (default), 1-Enabled;
+
+
+#Specify the IP address or domain name of the outbound proxy server.
+account.1.outbound_host = {$outbound_proxy_1}
+
+#Specify the server port, the default value is 5060.
+account.1.outbound_port = 5060
+
+#Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV;
+{if $sip_transport_1 == 'udp'}account.1.transport = 0{/if}
+{if $sip_transport_1 == 'tcp'}account.1.transport = 1{/if}
+{if $sip_transport_1 == 'tls'}account.1.transport = 2{/if}
+{if $sip_transport_1 == 'dns srv'}account.1.transport = 3{/if}
+
+account.1.outbound_proxy.1.address = {$outbound_proxy_primary_1}
+account.1.outbound_proxy.2.address = {$outbound_proxy_secondary_1}
+account.1.outbound_proxy_enable = {if isset($outbound_proxy_primary_1)}1{else}0{/if}
+
+{if isset($outbound_proxy_1_port)}
+account.1.outbound_proxy.1.port = {$outbound_proxy_1_port}
+{else}
+account.1.outbound_proxy.1.port = 5060
+{/if}
+{if isset($outbound_proxy_1_port)}
+account.1.outbound_proxy.2.port = {$outbound_proxy_2_port}
+{else}
+account.1.outbound_proxy.2.port = 5060
+{/if}
+
+#Configure the address of the backup outbound proxy server.
+account.1.backup_outbound_host =
+
+#Specify the port of the backup outbound proxy server, the default value is 5060.
+account.1.backup_outbound_port =
+
+
+#Enable or disable the anonymous call feature; 0-Disabled (default), 1-Enabled;
+account.1.anonymous_call =
+
+#Configure the on code and off code of the anonymous call feature.
+account.1.anonymous_call_oncode =
+account.1.anonymous_call_offcode =
+
+#Enable or disable the reject anonymous call feature; 0-Disabled (default), 1-Enabled;
+account.1.reject_anonymous_call =
+
+#Configure the on code and off code of the reject anonymous call feature.
+account.1.anonymous_reject_oncode =
+account.1.anonymous_reject_offcode =
+
+#Configure the SIP port for account 1, the default value is 5060.
+account.1.sip_listen_port =
+
+#Configure the register expiry time (in seconds), the default value is 3600.
+account.1.expires = {$register_expires_1}
+
+#Enable or disable the 100 reliable retransmission; 0-Disabled, 1-Enabled (default);
+account.1.100rel_enable = {$yealink_retransmission}
+
+#Enable or disable the resource reservation; 0-Disabled (default), 1-Enabled;
+account.1.precondition =
+
+#Enable or disable the phone to subscribe the register status; 0-Disabled (default), 1-Enabled;
+account.1.subscribe_register =
+
+#Enable or disable the phone to subscribe the message waiting indicator; 0-Disabled (default), 1-Enabled;
+account.1.subscribe_mwi = 0
+
+#Configure MWI subscribe expiry time (in seconds). It ranges from 0 to 84600, the default value is 3600.
+account.1.subscribe_mwi_expires = 3600
+
+#Configure the type of SIP header to carry the caller ID; 0-FROM (default), 1-PAI;
+account.1.cid_source =
+
+#Enable or disable the session timer; 0-Disabled (default), 1-Enabled;
+account.1.session_timer.enable = {$yealink_session_timer}
+
+#Configure the refresh session timer interval (in seconds). It ranges from 1 to 9999.
+account.1.session_timer.expires =
+
+#Configure the session timer refresher; 0-Uac (default), 1-Uas;
+account.1.session_timer.refresher =
+
+#Enable or disable the "user=phone"; 0-Disabled (default), 1-Enabled;
+account.1.enable_user_equal_phone =
+
+#Configure the way of encrypting the message; 0-Disabled (default), 1-Forced, 2-Negotiated;
+account.1.srtp_encryption = {$yealink_srtp_encryption}
+
+#Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60.
+account.1.ptime =
+
+#Enable or disable the phone to subscribe to the voicemail through the message waiting indicator; 0-Disabled (default), 1-Enabled;
+account.1.subscribe_mwi_to_vm = 0
+
+#Enable or disable the phone to send the MAC address in the Register message; 0-Disabled (default), 1-Enabled;
+account.1.register_mac =
+
+#Enable or disable the phone to send the line number in the Register message; 0-Disabled, 1-Enabled (default);
+account.1.register_line =
+
+#Configure the interval (in seconds) the phone retries to register when account 1 fails to register. It ranges from 0 to 1800, the default value is 30.
+account.1.reg_fail_retry_interval =
+
+#Enable or disable the SIP signal encode; 0-Disabled (default), 1-Enabled (RC 4);
+account.1.enable_signal_encode =
+
+#Configure the key for encoding.
+account.1.signal_encode_key =
+
+#Configure the DTMF type; 0-INBAND, 1-RFC2833 (default), 2-SIP INFO, 3-AUTO+SIP INFO;
+account.1.dtmf.type =
+
+#Configure the RFC2833 payload. It ranges from 96 to 225, the default value is 101.
+account.1.dtmf.dtmf_payload =
+
+#Configure the DTMF info type when using the SIP INFO; 0-Disabled, 1-DTMF-Relay (default), 2-DTMF, 3-Telephone-Event;
+account.1.dtmf.info_type =
+
+
+#######################################################################################
+##                                   NAT Settings                                    ##
+#######################################################################################
+
+#Enable or disable the NAT traversal; 0-Disabled (default), 1-STUN;
+account.1.nat.nat_traversal = {if isset($stun_server)}1{else}0{/if}
+
+#Configure the STUN server address.
+account.1.nat.stun_server = {$stun_server}
+
+#Configure the STUN server port, the default value is 3478.
+account.1.nat.stun_port = {if isset($stun_port)}{$stun_port}{else}3478{/if}
+
+#Enable or disable the NAT keep-alive; 0-Disabled, 1-Default (default), 2-Option, 3-Notify;
+account.1.nat.udp_update_enable = 3
+
+#Specify the keep-alive interval (in seconds), the default value is 30.
+account.1.nat.udp_update_time =
+
+#Enable or disable the NAT Rport; 0-Disabled (default), 1-Enabled;
+account.1.nat.rport = {$yealink_rport}
+
+#Configure the session timer (in seconds), the default values of T1, T2, T3 are 0.5, 4, 5.
+account.1.advanced.timer_t1 =
+account.1.advanced.timer_t2 =
+account.1.advanced.timer_t4 =
+
+account.1.codec.1.enable = 1
+account.1.codec.1.payload_type = PCMU
+account.1.codec.1.priority = 1
+account.1.codec.1.rtpmap = 0
+
+account.1.codec.2.enable = 1
+account.1.codec.2.payload_type = PCMA
+account.1.codec.2.priority = 2
+account.1.codec.2.rtpmap = 8
+
+account.1.codec.3.enable = 0
+account.1.codec.3.payload_type = G723_53
+account.1.codec.3.priority =0
+account.1.codec.3.rtpmap = 4
+
+account.1.codec.4.enable = 0
+account.1.codec.4.payload_type = G723_63
+account.1.codec.4.priority = 0
+account.1.codec.4.rtpmap = 4
+
+account.1.codec.5.enable = 1
+account.1.codec.5.payload_type = G729
+account.1.codec.5.priority = 3
+account.1.codec.5.rtpmap = 18
+
+account.1.codec.6.enable = 1
+account.1.codec.6.payload_type = G722
+account.1.codec.6.priority = 4
+account.1.codec.6.rtpmap = 9
+
+account.1.codec.7.enable = 0
+account.1.codec.7.payload_type = G726-32
+account.1.codec.7.priority = 0
+account.1.codec.7.rtpmap = 2
+
+account.1.codec.8.enable = 0
+account.1.codec.8.payload_type = iLBC_13_3
+account.1.codec.8.priority = 0
+account.1.codec.8.rtpmap = 97
+
+account.1.codec.9.enable = 0
+account.1.codec.9.payload_type = iLBC_15_2
+account.1.codec.9.priority = 0
+account.1.codec.9.rtpmap = 97
+
+#######################################################################################
+##         	                   Call Forward                                          ##
+#######################################################################################
+#Enable or disable the always forward, 0-Disabled(default), 1-Enabled;
+account.1.always_fwd.enable =
+
+#Configure the target phonenumber that the phone will forward the call to;
+account.1.always_fwd.target =
+
+#Configure the on/off code for always forward;
+
+
+#Enable or disable the busy forward, 0-Disabled(default), 1-Enabled;
+account.1.busy_fwd.enable =
+account.1.busy_fwd.target =
+
+
+#Enable or disable the no answer forward, 0-Disabled(default), 1-Enabled;
+#Configure the waiting ring times before forwarding, ranges from 0 to 20 (by default);
+account.1.timeout_fwd.enable =
+account.1.timeout_fwd.target =
+account.1.timeout_fwd.timeout =
+
+
+#######################################################################################
+##                          DND                                                      ##
+#######################################################################################
+
+#Configure the DND key mode; 0-Phone mode (default), 1-Custom mode.
+features.dnd_mode =
+
+#Enable or disable the DND feautre for account1; 0-Disabled (default), 1-Enabled;
+account.1.dnd.enable =
+
+#Configure the DND on code and off code for account1.
+
+account.1.sip_trust_ctrl = 1
+
+#######################################################################################
+##                                   Account2 Settings                               ##
+#######################################################################################
+
+#Enable or disable the account 1; 0-Disabled (default), 1-Enabled;
+account.2.enable = 1
+
+#Configure the label displayed on the LCD screen for account 1.
+account.2.label = {$display_name_2}
+
+#Configure the display name of account 1.
+account.2.display_name = {$display_name_2}
+
+#Configure the username and password for register authentication.
+account.2.auth_name = {$user_id_2}
+account.2.password = {$user_password_2}
+
+#Configure the register user name.
+account.2.user_name = {$user_id_2}
+
+#Configure the SIP server address.
+account.2.sip_server_host = {$server_address_2}
+
+#Specify the port for the SIP server. The default value is 5060.
+account.2.sip_server_port = {$sip_port_2}
+
+#Enable or disable to use the outbound proxy server; 0-Disabled (default), 1-Enabled;
+
+
+#Specify the IP address or domain name of the outbound proxy server.
+account.2.outbound_host =
+
+#Specify the server port, the default value is 5060.
+account.2.outbound_port =5060
+
+#Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV;
+{if $sip_transport_2 == 'udp'}account.2.transport = 0{/if}
+{if $sip_transport_2 == 'tcp'}account.2.transport = 1{/if}
+{if $sip_transport_2 == 'tls'}account.2.transport = 2{/if}
+{if $sip_transport_2 == 'dns srv'}account.2.transport = 3{/if}
+
+account.2.outbound_proxy.1.address = {$outbound_proxy_primary_2}
+account.2.outbound_proxy.2.address = {$outbound_proxy_secondary_2}
+account.2.outbound_proxy_enable = {if isset($outbound_proxy_primary_2)}1{else}0{/if}
+
+#Configure the address of the backup outbound proxy server.
+account.2.backup_outbound_host =
+
+#Specify the port of the backup outbound proxy server, the default value is 5060.
+account.2.backup_outbound_port =
+
+
+#Enable or disable the anonymous call feature; 0-Disabled (default), 1-Enabled;
+account.2.anonymous_call =
+
+#Configure the on code and off code of the anonymous call feature.
+account.2.anonymous_call_oncode =
+account.2.anonymous_call_offcode =
+
+#Enable or disable the reject anonymous call feature; 0-Disabled (default), 1-Enabled;
+account.2.reject_anonymous_call =
+
+#Configure the on code and off code of the reject anonymous call feature.
+account.2.anonymous_reject_oncode =
+account.2.anonymous_reject_offcode =
+
+#Configure the SIP port for account 1, the default value is 5060.
+account.2.sip_listen_port =
+
+#Configure the register expiry time (in seconds), the default value is 3600.
+account.2.expires = {$register_expires_2}
+
+#Enable or disable the 100 reliable retransmission; 0-Disabled, 1-Enabled (default);
+account.2.100rel_enable = {$yealink_retransmission}
+
+#Enable or disable the resource reservation; 0-Disabled (default), 1-Enabled;
+account.2.precondition =
+
+#Enable or disable the phone to subscribe the register status; 0-Disabled (default), 1-Enabled;
+account.2.subscribe_register =
+
+#Enable or disable the phone to subscribe the message waiting indicator; 0-Disabled (default), 1-Enabled;
+account.2.subscribe_mwi = 0
+
+#Configure MWI subscribe expiry time (in seconds). It ranges from 0 to 84600, the default value is 3600.
+account.2.subscribe_mwi_expires = 3600
+
+#Configure the type of SIP header to carry the caller ID; 0-FROM (default), 1-PAI;
+account.2.cid_source =
+
+#Enable or disable the session timer; 0-Disabled (default), 1-Enabled;
+account.2.session_timer.enable = {$yealink_session_timer}
+
+#Configure the refresh session timer interval (in seconds). It ranges from 1 to 9999.
+account.2.session_timer.expires =
+
+#Configure the session timer refresher; 0-Uac (default), 1-Uas;
+account.2.session_timer.refresher =
+
+#Enable or disable the "user=phone"; 0-Disabled (default), 1-Enabled;
+account.2.enable_user_equal_phone =
+
+#Configure the way of encrypting the message; 0-Disabled (default), 1-Forced, 2-Negotiated;
+account.2.srtp_encryption =
+
+#Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60.
+account.2.ptime =
+
+#Enable or disable the phone to subscribe to the voicemail through the message waiting indicator; 0-Disabled (default), 1-Enabled;
+account.2.subscribe_mwi_to_vm = 0
+
+#Enable or disable the phone to send the MAC address in the Register message; 0-Disabled (default), 1-Enabled;
+account.2.register_mac =
+
+#Enable or disable the phone to send the line number in the Register message; 0-Disabled, 1-Enabled (default);
+account.2.register_line =
+
+#Configure the interval (in seconds) the phone retries to register when account 1 fails to register. It ranges from 0 to 1800, the default value is 30.
+account.2.reg_fail_retry_interval =
+
+#Enable or disable the SIP signal encode; 0-Disabled (default), 1-Enabled (RC 4);
+account.2.enable_signal_encode =
+
+#Configure the key for encoding.
+account.2.signal_encode_key =
+
+#Configure the DTMF type; 0-INBAND, 1-RFC2833 (default), 2-SIP INFO, 3-AUTO+SIP INFO;
+account.2.dtmf.type =
+
+#Configure the RFC2833 payload. It ranges from 96 to 225, the default value is 101.
+account.2.dtmf.dtmf_payload =
+
+#Configure the DTMF info type when using the SIP INFO; 0-Disabled, 1-DTMF-Relay (default), 2-DTMF, 3-Telephone-Event;
+account.2.dtmf.info_type =
+
+
+#######################################################################################
+##                                   NAT Settings                                    ##
+#######################################################################################
+
+#Enable or disable the NAT traversal; 0-Disabled (default), 1-STUN;
+account.2.nat.nat_traversal = {if isset($stun_server)}1{else}0{/if}
+
+#Configure the STUN server address.
+account.2.nat.stun_server = {$stun_server}
+
+#Configure the STUN server port, the default value is 3478.
+account.2.nat.stun_port = {if isset($stun_port)}{$stun_port}{else}3478{/if}
+
+#Enable or disable the NAT keep-alive; 0-Disabled, 1-Enabled (default);
+account.2.nat.udp_update_enable =
+
+#Specify the keep-alive interval (in seconds), the default value is 30.
+account.2.nat.udp_update_time =
+
+#Enable or disable the NAT Rport; 0-Disabled (default), 1-Enabled;
+account.2.nat.rport = {$yealink_rport}
+
+#Configure the session timer (in seconds), the default values of T1, T2, T3 are 0.5, 4, 5.
+account.2.advanced.timer_t1 =
+account.2.advanced.timer_t2 =
+account.2.advanced.timer_t4 =
+
+account.2.codec.1.enable = 1
+account.2.codec.1.payload_type = PCMU
+account.2.codec.1.priority = 1
+account.2.codec.1.rtpmap = 0
+
+account.2.codec.2.enable = 1
+account.2.codec.2.payload_type = PCMA
+account.2.codec.2.priority = 2
+account.2.codec.2.rtpmap = 8
+
+account.2.codec.3.enable = 0
+account.2.codec.3.payload_type = G723_53
+account.2.codec.3.priority =0
+account.2.codec.3.rtpmap = 4
+
+account.2.codec.4.enable = 0
+account.2.codec.4.payload_type = G723_63
+account.2.codec.4.priority = 0
+account.2.codec.4.rtpmap = 4
+
+account.2.codec.5.enable = 1
+account.2.codec.5.payload_type = G729
+account.2.codec.5.priority = 3
+account.2.codec.5.rtpmap = 18
+
+account.2.codec.6.enable = 1
+account.2.codec.6.payload_type = G722
+account.2.codec.6.priority = 4
+account.2.codec.6.rtpmap = 9
+
+account.2.codec.7.enable = 0
+account.2.codec.7.payload_type = G726-32
+account.2.codec.7.priority = 0
+account.2.codec.7.rtpmap = 2
+
+account.2.codec.8.enable = 0
+account.2.codec.8.payload_type = iLBC_13_3
+account.2.codec.8.priority = 0
+account.2.codec.8.rtpmap = 97
+
+account.2.codec.9.enable = 0
+account.2.codec.9.payload_type = iLBC_15_2
+account.2.codec.9.priority = 0
+account.2.codec.9.rtpmap = 97
+
+#######################################################################################
+##         	                   Call Forward                                          ##
+#######################################################################################
+#Enable or disable the always forward, 0-Disabled(default), 1-Enabled;
+account.2.always_fwd.enable =
+
+#Configure the target phonenumber that the phone will forward the call to;
+account.2.always_fwd.target =
+
+#Configure the on/off code for always forward;
+
+
+#Enable or disable the busy forward, 0-Disabled(default), 1-Enabled;
+account.2.busy_fwd.enable =
+account.2.busy_fwd.target =
+
+
+#Enable or disable the no answer forward, 0-Disabled(default), 1-Enabled;
+#Configure the waiting ring times before forwarding, ranges from 0 to 20 (by default);
+account.2.timeout_fwd.enable =
+account.2.timeout_fwd.target =
+account.2.timeout_fwd.timeout =
+
+
+#######################################################################################
+##                          DND                                                      ##
+#######################################################################################
+
+#Configure the DND key mode; 0-Phone mode (default), 1-Custom mode.
+features.dnd_mode =
+
+#Enable or disable the DND feautre for account2; 0-Disabled (default), 1-Enabled;
+account.2.dnd.enable =
+
+#Configure the DND on code and off code for account1.
+
+account.2.sip_trust_ctrl = 1
+
+#######################################################################################
+##                                   Account3 Settings                               ##
+#######################################################################################
+
+#Enable or disable the account 1; 0-Disabled (default), 1-Enabled;
+account.3.enable = 1
+
+#Configure the label displayed on the LCD screen for account 1.
+account.3.label = {$display_name_3}
+
+#Configure the display name of account 1.
+account.3.display_name = {$display_name_3}
+
+#Configure the username and password for register authentication.
+account.3.auth_name = {$user_id_3}
+account.3.password = {$user_password_3}
+
+#Configure the register user name.
+account.3.user_name = {$user_id_3}
+
+#Configure the SIP server address.
+account.3.sip_server_host = {$server_address_3}
+
+#Specify the port for the SIP server. The default value is 5060.
+account.3.sip_server_port = {$sip_port_3}
+
+#Enable or disable to use the outbound proxy server; 0-Disabled (default), 1-Enabled;
+
+
+#Specify the IP address or domain name of the outbound proxy server.
+account.3.outbound_host = {$outbound_proxy_3}
+
+#Specify the server port, the default value is 5060.
+account.3.outbound_port = 5060
+
+#Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV;
+{if $sip_transport_3 == 'udp'}account.3.transport = 0{/if}
+{if $sip_transport_3 == 'tcp'}account.3.transport = 1{/if}
+{if $sip_transport_3 == 'tls'}account.3.transport = 2{/if}
+{if $sip_transport_3 == 'dns srv'}account.3.transport = 3{/if}
+
+account.3.outbound_proxy.1.address = {$outbound_proxy_primary_3}
+account.3.outbound_proxy.2.address = {$outbound_proxy_secondary_3}
+account.3.outbound_proxy_enable = {if isset($outbound_proxy_primary_3)}1{else}0{/if}
+
+#Configure the address of the backup outbound proxy server.
+account.3.backup_outbound_host =
+
+#Specify the port of the backup outbound proxy server, the default value is 5060.
+account.3.backup_outbound_port =
+
+
+#Enable or disable the anonymous call feature; 0-Disabled (default), 1-Enabled;
+account.3.anonymous_call =
+
+#Configure the on code and off code of the anonymous call feature.
+account.3.anonymous_call_oncode =
+account.3.anonymous_call_offcode =
+
+#Enable or disable the reject anonymous call feature; 0-Disabled (default), 1-Enabled;
+account.3.reject_anonymous_call =
+
+#Configure the on code and off code of the reject anonymous call feature.
+account.3.anonymous_reject_oncode =
+account.3.anonymous_reject_offcode =
+
+#Configure the SIP port for account 1, the default value is 5060.
+account.3.sip_listen_port =
+
+#Configure the register expiry time (in seconds), the default value is 3600.
+account.3.expires = {$register_expires_3}
+
+#Enable or disable the 100 reliable retransmission; 0-Disabled, 1-Enabled (default);
+account.3.100rel_enable = {$yealink_retransmission}
+
+#Enable or disable the resource reservation; 0-Disabled (default), 1-Enabled;
+account.3.precondition =
+
+#Enable or disable the phone to subscribe the register status; 0-Disabled (default), 1-Enabled;
+account.3.subscribe_register =
+
+#Enable or disable the phone to subscribe the message waiting indicator; 0-Disabled (default), 1-Enabled;
+account.3.subscribe_mwi = 0
+
+#Configure MWI subscribe expiry time (in seconds). It ranges from 0 to 84600, the default value is 3600.
+account.3.subscribe_mwi_expires = 3600
+
+#Configure the type of SIP header to carry the caller ID; 0-FROM (default), 1-PAI;
+account.3.cid_source =
+
+#Enable or disable the session timer; 0-Disabled (default), 1-Enabled;
+account.3.session_timer.enable = {$yealink_session_timer}
+
+#Configure the refresh session timer interval (in seconds). It ranges from 1 to 9999.
+account.3.session_timer.expires =
+
+#Configure the session timer refresher; 0-Uac (default), 1-Uas;
+account.3.session_timer.refresher =
+
+#Enable or disable the "user=phone"; 0-Disabled (default), 1-Enabled;
+account.3.enable_user_equal_phone =
+
+#Configure the way of encrypting the message; 0-Disabled (default), 1-Forced, 2-Negotiated;
+account.3.srtp_encryption =
+
+#Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60.
+account.3.ptime =
+
+#Enable or disable the phone to subscribe to the voicemail through the message waiting indicator; 0-Disabled (default), 1-Enabled;
+account.3.subscribe_mwi_to_vm = 0
+
+#Enable or disable the phone to send the MAC address in the Register message; 0-Disabled (default), 1-Enabled;
+account.3.register_mac =
+
+#Enable or disable the phone to send the line number in the Register message; 0-Disabled, 1-Enabled (default);
+account.3.register_line =
+
+#Configure the interval (in seconds) the phone retries to register when account 1 fails to register. It ranges from 0 to 1800, the default value is 30.
+account.3.reg_fail_retry_interval =
+
+#Enable or disable the SIP signal encode; 0-Disabled (default), 1-Enabled (RC 4);
+account.3.enable_signal_encode =
+
+#Configure the key for encoding.
+account.3.signal_encode_key =
+
+#Configure the DTMF type; 0-INBAND, 1-RFC2833 (default), 2-SIP INFO, 3-AUTO+SIP INFO;
+account.3.dtmf.type =
+
+#Configure the RFC2833 payload. It ranges from 96 to 225, the default value is 101.
+account.3.dtmf.dtmf_payload =
+
+#Configure the DTMF info type when using the SIP INFO; 0-Disabled, 1-DTMF-Relay (default), 2-DTMF, 3-Telephone-Event;
+account.3.dtmf.info_type =
+
+
+#######################################################################################
+##                                   NAT Settings                                    ##
+#######################################################################################
+
+#Enable or disable the NAT traversal; 0-Disabled (default), 1-STUN;
+account.3.nat.nat_traversal = {if isset($stun_server)}1{else}0{/if}
+
+#Configure the STUN server address.
+account.3.nat.stun_server = {$stun_server}
+
+#Configure the STUN server port, the default value is 3478.
+account.3.nat.stun_port = {if isset($stun_port)}{$stun_port}{else}3478{/if}
+
+#Enable or disable the NAT keep-alive; 0-Disabled, 1-Enabled (default);
+account.3.nat.udp_update_enable =
+
+#Specify the keep-alive interval (in seconds), the default value is 30.
+account.3.nat.udp_update_time =
+
+#Enable or disable the NAT Rport; 0-Disabled (default), 1-Enabled;
+account.3.nat.rport = {$yealink_rport}
+
+#Configure the session timer (in seconds), the default values of T1, T2, T3 are 0.5, 4, 5.
+account.3.advanced.timer_t1 =
+account.3.advanced.timer_t2 =
+account.3.advanced.timer_t4 =
+
+account.3.codec.1.enable = 1
+account.3.codec.1.payload_type = PCMU
+account.3.codec.1.priority = 1
+account.3.codec.1.rtpmap = 0
+
+account.3.codec.2.enable = 1
+account.3.codec.2.payload_type = PCMA
+account.3.codec.2.priority = 2
+account.3.codec.2.rtpmap = 8
+
+account.3.codec.3.enable = 0
+account.3.codec.3.payload_type = G723_53
+account.3.codec.3.priority =0
+account.3.codec.3.rtpmap = 4
+
+account.3.codec.4.enable = 0
+account.3.codec.4.payload_type = G723_63
+account.3.codec.4.priority = 0
+account.3.codec.4.rtpmap = 4
+
+account.3.codec.5.enable = 1
+account.3.codec.5.payload_type = G729
+account.3.codec.5.priority = 3
+account.3.codec.5.rtpmap = 18
+
+account.3.codec.6.enable = 1
+account.3.codec.6.payload_type = G722
+account.3.codec.6.priority = 4
+account.3.codec.6.rtpmap = 9
+
+account.3.codec.7.enable = 0
+account.3.codec.7.payload_type = G726-32
+account.3.codec.7.priority = 0
+account.3.codec.7.rtpmap = 2
+
+account.3.codec.8.enable = 0
+account.3.codec.8.payload_type = iLBC_13_3
+account.3.codec.8.priority = 0
+account.3.codec.8.rtpmap = 97
+
+account.3.codec.9.enable = 0
+account.3.codec.9.payload_type = iLBC_15_2
+account.3.codec.9.priority = 0
+account.3.codec.9.rtpmap = 97
+
+#######################################################################################
+##         	                   Call Forward                                          ##
+#######################################################################################
+#Enable or disable the always forward, 0-Disabled(default), 1-Enabled;
+account.3.always_fwd.enable =
+
+#Configure the target phonenumber that the phone will forward the call to;
+account.3.always_fwd.target =
+
+#Configure the on/off code for always forward;
+
+
+#Enable or disable the busy forward, 0-Disabled(default), 1-Enabled;
+account.3.busy_fwd.enable =
+account.3.busy_fwd.target =
+
+
+#Enable or disable the no answer forward, 0-Disabled(default), 1-Enabled;
+#Configure the waiting ring times before forwarding, ranges from 0 to 20 (by default);
+account.3.timeout_fwd.enable =
+account.3.timeout_fwd.target =
+account.3.timeout_fwd.timeout =
+
+
+#######################################################################################
+##                          DND                                                      ##
+#######################################################################################
+
+#Configure the DND key mode; 0-Phone mode (default), 1-Custom mode.
+features.dnd_mode =
+
+#Enable or disable the DND feautre for account3; 0-Disabled (default), 1-Enabled;
+account.3.dnd.enable =
+
+#Configure the DND on code and off code for account3.
+
+account.3.sip_trust_ctrl = 1
+
+#######################################################################################
+##                                   Account4 Settings                               ##
+#######################################################################################
+
+#Enable or disable the account 1; 0-Disabled (default), 1-Enabled;
+account.4.enable =
+
+#Configure the label displayed on the LCD screen for account 1.
+account.4.label =
+
+#Configure the display name of account 1.
+account.4.display_name =
+
+#Configure the username and password for register authentication.
+account.4.auth_name =
+account.4.password =
+
+#Configure the register user name.
+account.4.user_name =
+
+#Configure the SIP server address.
+account.4.sip_server_host =
+
+#Specify the port for the SIP server. The default value is 5060.
+account.4.sip_server_port = {$sip_port_4}
+
+#Enable or disable to use the outbound proxy server; 0-Disabled (default), 1-Enabled;
+
+
+#Specify the IP address or domain name of the outbound proxy server.
+account.4.outbound_host =
+
+#Specify the server port, the default value is 5060.
+account.4.outbound_port =
+
+#Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV;
+{if $sip_transport_4 == 'udp'}account.4.transport = 0{/if}
+{if $sip_transport_4 == 'tcp'}account.4.transport = 1{/if}
+{if $sip_transport_4 == 'tls'}account.4.transport = 2{/if}
+{if $sip_transport_4 == 'dns srv'}account.4.transport = 3{/if}
+
+account.4.outbound_proxy.1.address = {$outbound_proxy_primary_4}
+account.4.outbound_proxy.2.address = {$outbound_proxy_secondary_4}
+account.4.outbound_proxy_enable = {if isset($outbound_proxy_primary_4)}1{else}0{/if}
+
+
+#Configure the address of the backup outbound proxy server.
+account.4.backup_outbound_host =
+
+#Specify the port of the backup outbound proxy server, the default value is 5060.
+account.4.backup_outbound_port =
+
+
+#Enable or disable the anonymous call feature; 0-Disabled (default), 1-Enabled;
+account.4.anonymous_call =
+
+#Configure the on code and off code of the anonymous call feature.
+account.4.anonymous_call_oncode =
+account.4.anonymous_call_offcode =
+
+#Enable or disable the reject anonymous call feature; 0-Disabled (default), 1-Enabled;
+account.4.reject_anonymous_call =
+
+#Configure the on code and off code of the reject anonymous call feature.
+account.4.anonymous_reject_oncode =
+account.4.anonymous_reject_offcode =
+
+#Configure the SIP port for account 1, the default value is 5060.
+account.4.sip_listen_port =
+
+#Configure the register expiry time (in seconds), the default value is 3600.
+account.4.expires = {$register_expires_4}
+
+#Enable or disable the 100 reliable retransmission; 0-Disabled, 1-Enabled (default);
+account.4.100rel_enable = {$yealink_retransmission}
+
+#Enable or disable the resource reservation; 0-Disabled (default), 1-Enabled;
+account.4.precondition =
+
+#Enable or disable the phone to subscribe the register status; 0-Disabled (default), 1-Enabled;
+account.4.subscribe_register =
+
+#Enable or disable the phone to subscribe the message waiting indicator; 0-Disabled (default), 1-Enabled;
+account.4.subscribe_mwi = 0
+
+#Configure MWI subscribe expiry time (in seconds). It ranges from 0 to 84600, the default value is 3600.
+account.4.subscribe_mwi_expires = 3600
+
+#Configure the type of SIP header to carry the caller ID; 0-FROM (default), 1-PAI;
+account.4.cid_source =
+
+#Enable or disable the session timer; 0-Disabled (default), 1-Enabled;
+account.4.session_timer.enable = {$yealink_session_timer}
+
+#Configure the refresh session timer interval (in seconds). It ranges from 1 to 9999.
+account.4.session_timer.expires =
+
+#Configure the session timer refresher; 0-Uac (default), 1-Uas;
+account.4.session_timer.refresher =
+
+#Enable or disable the "user=phone"; 0-Disabled (default), 1-Enabled;
+account.4.enable_user_equal_phone =
+
+#Configure the way of encrypting the message; 0-Disabled (default), 1-Forced, 2-Negotiated;
+account.4.srtp_encryption =
+
+#Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60.
+account.4.ptime =
+
+#Enable or disable the phone to subscribe to the voicemail through the message waiting indicator; 0-Disabled (default), 1-Enabled;
+account.4.subscribe_mwi_to_vm = 0
+
+#Enable or disable the phone to send the MAC address in the Register message; 0-Disabled (default), 1-Enabled;
+account.4.register_mac =
+
+#Enable or disable the phone to send the line number in the Register message; 0-Disabled, 1-Enabled (default);
+account.4.register_line =
+
+#Configure the interval (in seconds) the phone retries to register when account 1 fails to register. It ranges from 0 to 1800, the default value is 30.
+account.4.reg_fail_retry_interval =
+
+#Enable or disable the SIP signal encode; 0-Disabled (default), 1-Enabled (RC 4);
+account.4.enable_signal_encode =
+
+#Configure the key for encoding.
+account.4.signal_encode_key =
+
+#Configure the DTMF type; 0-INBAND, 1-RFC2833 (default), 2-SIP INFO, 3-AUTO+SIP INFO;
+account.4.dtmf.type =
+
+#Configure the RFC2833 payload. It ranges from 96 to 225, the default value is 101.
+account.4.dtmf.dtmf_payload =
+
+#Configure the DTMF info type when using the SIP INFO; 0-Disabled, 1-DTMF-Relay (default), 2-DTMF, 3-Telephone-Event;
+account.4.dtmf.info_type =
+
+
+#######################################################################################
+##                                   NAT Settings                                    ##
+#######################################################################################
+
+#Enable or disable the NAT traversal; 0-Disabled (default), 1-STUN;
+account.4.nat.nat_traversal = {if isset($stun_server)}1{else}0{/if}
+
+#Configure the STUN server address.
+account.4.nat.stun_server = {$stun_server}
+
+#Configure the STUN server port, the default value is 3478.
+account.4.nat.stun_port = {if isset($stun_port)}{$stun_port}{else}3478{/if}
+
+#Enable or disable the NAT keep-alive; 0-Disabled, 1-Enabled (default);
+account.4.nat.udp_update_enable =
+
+#Specify the keep-alive interval (in seconds), the default value is 30.
+account.4.nat.udp_update_time =
+
+#Enable or disable the NAT Rport; 0-Disabled (default), 1-Enabled;
+account.4.nat.rport = {$yealink_rport}
+
+#Configure the session timer (in seconds), the default values of T1, T2, T3 are 0.5, 4, 5.
+account.4.advanced.timer_t1 =
+account.4.advanced.timer_t2 =
+account.4.advanced.timer_t4 =
+
+
+account.4.codec.1.enable = 1
+account.4.codec.1.payload_type = PCMU
+account.4.codec.1.priority = 1
+account.4.codec.1.rtpmap = 0
+
+account.4.codec.2.enable = 1
+account.4.codec.2.payload_type = PCMA
+account.4.codec.2.priority = 2
+account.4.codec.2.rtpmap = 8
+
+account.4.codec.3.enable = 0
+account.4.codec.3.payload_type = G723_53
+account.4.codec.3.priority =0
+account.4.codec.3.rtpmap = 4
+
+account.4.codec.4.enable = 0
+account.4.codec.4.payload_type = G723_63
+account.4.codec.4.priority = 0
+account.4.codec.4.rtpmap = 4
+
+account.4.codec.5.enable = 1
+account.4.codec.5.payload_type = G729
+account.4.codec.5.priority = 3
+account.4.codec.5.rtpmap = 18
+
+account.4.codec.6.enable = 1
+account.4.codec.6.payload_type = G722
+account.4.codec.6.priority = 4
+account.4.codec.6.rtpmap = 9
+
+account.4.codec.7.enable = 0
+account.4.codec.7.payload_type = G726-32
+account.4.codec.7.priority = 0
+account.4.codec.7.rtpmap = 2
+
+account.4.codec.8.enable = 0
+account.4.codec.8.payload_type = iLBC_13_3
+account.4.codec.8.priority = 0
+account.4.codec.8.rtpmap = 97
+
+account.4.codec.9.enable = 0
+account.4.codec.9.payload_type = iLBC_15_2
+account.4.codec.9.priority = 0
+account.4.codec.9.rtpmap = 97
+
+#######################################################################################
+##         	                   Call Forward                                          ##
+#######################################################################################
+#Enable or disable the always forward, 0-Disabled(default), 1-Enabled;
+account.4.always_fwd.enable =
+
+#Configure the target phonenumber that the phone will forward the call to;
+account.4.always_fwd.target =
+
+#Configure the on/off code for always forward;
+
+
+#Enable or disable the busy forward, 0-Disabled(default), 1-Enabled;
+account.4.busy_fwd.enable =
+account.4.busy_fwd.target =
+
+
+#Enable or disable the no answer forward, 0-Disabled(default), 1-Enabled;
+#Configure the waiting ring times before forwarding, ranges from 0 to 20 (by default);
+account.4.timeout_fwd.enable =
+account.4.timeout_fwd.target =
+account.4.timeout_fwd.timeout =
+
+
+#######################################################################################
+##                          DND                                                      ##
+#######################################################################################
+
+#Configure the DND key mode; 0-Phone mode (default), 1-Custom mode.
+features.dnd_mode =
+
+#Enable or disable the DND feautre for account4; 0-Disabled (default), 1-Enabled;
+account.4.dnd.enable =
+
+#Configure the DND on code and off code for account4.
+
+account.4.sip_trust_ctrl = 1
+
+#######################################################################################
+##                                   Account5 Settings                               ##
+#######################################################################################
+
+#Enable or disable the account 1; 0-Disabled (default), 1-Enabled;
+account.5.enable =
+
+#Configure the label displayed on the LCD screen for account 1.
+account.5.label =
+
+#Configure the display name of account 1.
+account.5.display_name =
+
+#Configure the username and password for register authentication.
+account.5.auth_name =
+account.5.password =
+
+#Configure the register user name.
+account.5.user_name =
+
+#Configure the SIP server address.
+account.5.sip_server_host =
+
+#Specify the port for the SIP server. The default value is 5060.
+account.5.sip_server_port = {$sip_port_5}
+
+#Enable or disable to use the outbound proxy server; 0-Disabled (default), 1-Enabled;
+
+
+#Specify the IP address or domain name of the outbound proxy server.
+account.5.outbound_host =
+
+#Specify the server port, the default value is 5060.
+account.5.outbound_port =
+
+#Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV;
+{if $sip_transport_5 == 'udp'}account.5.transport = 0{/if}
+{if $sip_transport_5 == 'tcp'}account.5.transport = 1{/if}
+{if $sip_transport_5 == 'tls'}account.5.transport = 2{/if}
+{if $sip_transport_5 == 'dns srv'}account.5.transport = 3{/if}
+
+account.5.outbound_proxy.1.address = {$outbound_proxy_primary_5}
+account.5.outbound_proxy.2.address = {$outbound_proxy_secondary_5}
+account.5.outbound_proxy_enable = {if isset($outbound_proxy_primary_5)}1{else}0{/if}
+
+#Configure the address of the backup outbound proxy server.
+account.5.backup_outbound_host =
+
+#Specify the port of the backup outbound proxy server, the default value is 5060.
+account.5.backup_outbound_port =
+
+
+#Enable or disable the anonymous call feature; 0-Disabled (default), 1-Enabled;
+account.5.anonymous_call =
+
+#Configure the on code and off code of the anonymous call feature.
+account.5.anonymous_call_oncode =
+account.5.anonymous_call_offcode =
+
+#Enable or disable the reject anonymous call feature; 0-Disabled (default), 1-Enabled;
+account.5.reject_anonymous_call =
+
+#Configure the on code and off code of the reject anonymous call feature.
+account.5.anonymous_reject_oncode =
+account.5.anonymous_reject_offcode =
+
+#Configure the SIP port for account 1, the default value is 5060.
+account.5.sip_listen_port =
+
+#Configure the register expiry time (in seconds), the default value is 3600.
+account.5.expires = {$register_expires_5}
+
+#Enable or disable the 100 reliable retransmission; 0-Disabled, 1-Enabled (default);
+account.5.100rel_enable = {$yealink_retransmission}
+
+#Enable or disable the resource reservation; 0-Disabled (default), 1-Enabled;
+account.5.precondition =
+
+#Enable or disable the phone to subscribe the register status; 0-Disabled (default), 1-Enabled;
+account.5.subscribe_register =
+
+#Enable or disable the phone to subscribe the message waiting indicator; 0-Disabled (default), 1-Enabled;
+account.5.subscribe_mwi = 0
+
+#Configure MWI subscribe expiry time (in seconds). It ranges from 0 to 84600, the default value is 3600.
+account.5.subscribe_mwi_expires = 3600
+
+#Configure the type of SIP header to carry the caller ID; 0-FROM (default), 1-PAI;
+account.5.cid_source =
+
+#Enable or disable the session timer; 0-Disabled (default), 1-Enabled;
+account.5.session_timer.enable = {$yealink_session_timer}
+
+#Configure the refresh session timer interval (in seconds). It ranges from 1 to 9999.
+account.5.session_timer.expires =
+
+#Configure the session timer refresher; 0-Uac (default), 1-Uas;
+account.5.session_timer.refresher =
+
+#Enable or disable the "user=phone"; 0-Disabled (default), 1-Enabled;
+account.5.enable_user_equal_phone =
+
+#Configure the way of encrypting the message; 0-Disabled (default), 1-Forced, 2-Negotiated;
+account.5.srtp_encryption =
+
+#Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60.
+account.5.ptime =
+
+#Enable or disable the phone to subscribe to the voicemail through the message waiting indicator; 0-Disabled (default), 1-Enabled;
+account.5.subscribe_mwi_to_vm = 0
+
+#Enable or disable the phone to send the MAC address in the Register message; 0-Disabled (default), 1-Enabled;
+account.5.register_mac =
+
+#Enable or disable the phone to send the line number in the Register message; 0-Disabled, 1-Enabled (default);
+account.5.register_line =
+
+#Configure the interval (in seconds) the phone retries to register when account 1 fails to register. It ranges from 0 to 1800, the default value is 30.
+account.5.reg_fail_retry_interval =
+
+#Enable or disable the SIP signal encode; 0-Disabled (default), 1-Enabled (RC 4);
+account.5.enable_signal_encode =
+
+#Configure the key for encoding.
+account.5.signal_encode_key =
+
+#Configure the DTMF type; 0-INBAND, 1-RFC2833 (default), 2-SIP INFO, 3-AUTO+SIP INFO;
+account.5.dtmf.type =
+
+#Configure the RFC2833 payload. It ranges from 96 to 225, the default value is 101.
+account.5.dtmf.dtmf_payload =
+
+#Configure the DTMF info type when using the SIP INFO; 0-Disabled, 1-DTMF-Relay (default), 2-DTMF, 3-Telephone-Event;
+account.5.dtmf.info_type =
+
+
+#######################################################################################
+##                                   NAT Settings                                    ##
+#######################################################################################
+
+#Enable or disable the NAT traversal; 0-Disabled (default), 1-STUN;
+account.5.nat.nat_traversal = {if isset($stun_server)}1{else}0{/if}
+
+#Configure the STUN server address.
+account.5.nat.stun_server = {$stun_server}
+
+#Configure the STUN server port, the default value is 3478.
+account.5.nat.stun_port = {if isset($stun_port)}{$stun_port}{else}3478{/if}
+
+#Enable or disable the NAT keep-alive; 0-Disabled, 1-Enabled (default);
+account.5.nat.udp_update_enable =
+
+#Specify the keep-alive interval (in seconds), the default value is 30.
+account.5.nat.udp_update_time =
+
+#Enable or disable the NAT Rport; 0-Disabled (default), 1-Enabled;
+account.5.nat.rport = {$yealink_rport}
+
+#Configure the session timer (in seconds), the default values of T1, T2, T3 are 0.5, 4, 5.
+account.5.advanced.timer_t1 =
+account.5.advanced.timer_t2 =
+account.5.advanced.timer_t4 =
+
+account.5.codec.1.enable = 1
+account.5.codec.1.payload_type = PCMU
+account.5.codec.1.priority = 1
+account.5.codec.1.rtpmap = 0
+
+account.5.codec.2.enable = 1
+account.5.codec.2.payload_type = PCMA
+account.5.codec.2.priority = 2
+account.5.codec.2.rtpmap = 8
+
+account.5.codec.3.enable = 0
+account.5.codec.3.payload_type = G723_53
+account.5.codec.3.priority =0
+account.5.codec.3.rtpmap = 4
+
+account.5.codec.4.enable = 0
+account.5.codec.4.payload_type = G723_63
+account.5.codec.4.priority = 0
+account.5.codec.4.rtpmap = 4
+
+account.5.codec.5.enable = 1
+account.5.codec.5.payload_type = G729
+account.5.codec.5.priority = 3
+account.5.codec.5.rtpmap = 18
+
+account.5.codec.6.enable = 1
+account.5.codec.6.payload_type = G722
+account.5.codec.6.priority = 4
+account.5.codec.6.rtpmap = 9
+
+account.5.codec.7.enable = 0
+account.5.codec.7.payload_type = G726-32
+account.5.codec.7.priority = 0
+account.5.codec.7.rtpmap = 2
+
+account.5.codec.8.enable = 0
+account.5.codec.8.payload_type = iLBC_13_3
+account.5.codec.8.priority = 0
+account.5.codec.8.rtpmap = 97
+
+account.5.codec.9.enable = 0
+account.5.codec.9.payload_type = iLBC_15_2
+account.5.codec.9.priority = 0
+account.5.codec.9.rtpmap = 97
+
+#######################################################################################
+##         	                   Call Forward                                          ##
+#######################################################################################
+#Enable or disable the always forward, 0-Disabled(default), 1-Enabled;
+account.5.always_fwd.enable =
+
+#Configure the target phonenumber that the phone will forward the call to;
+account.5.always_fwd.target =
+
+#Configure the on/off code for always forward;
+
+
+#Enable or disable the busy forward, 0-Disabled(default), 1-Enabled;
+account.5.busy_fwd.enable =
+account.5.busy_fwd.target =
+
+
+#Enable or disable the no answer forward, 0-Disabled(default), 1-Enabled;
+#Configure the waiting ring times before forwarding, ranges from 0 to 20 (by default);
+account.5.timeout_fwd.enable =
+account.5.timeout_fwd.target =
+account.5.timeout_fwd.timeout =
+
+
+#######################################################################################
+##                          DND                                                      ##
+#######################################################################################
+
+#Configure the DND key mode; 0-Phone mode (default), 1-Custom mode.
+features.dnd_mode =
+
+#Enable or disable the DND feautre for account5; 0-Disabled (default), 1-Enabled;
+account.5.dnd.enable =
+
+#Configure the DND on code and off code for account5.
+
+account.5.sip_trust_ctrl = 1
+
+voice_mail.number.1 = {$voicemail_number}
+
+#######################################################################################
+##                                   Network                                         ##
+#######################################################################################
+
+#Configure the WAN port type; 0-DHCP(default), 1-PPPoE, 2-Static IP Address;
+#Require reboot;
+network.internet_port.type =
+
+#Configure the static IP address, submask, gateway and DNS server.
+#Require reboot;
+network.internet_port.ip =
+network.internet_port.mask =
+network.internet_port.gateway =
+{if isset($dns_server_primary)}network.primary_dns = {$dns_server_primary}{/if}
+{if isset($dns_server_secondary)}network.secondary_dns = {$dns_server_secondary}{/if}
+{if isset($dns_server_primary)}network.static_dns_enable = 1{else}network.static_dns_enable = 0{/if}